2大家快来帮我翻译!?

For claws, make three small sausages of newspaper and tape them together at one end.

Do the same again, and you'll have two claws.

For the head, mould some more newspaper into a sort of pear shape, and bend the thin end over to make a small, beaky nose.

For the bottom jaw, sculpt some newspaper into a rough triangle.

Stick that to the underneath of the head with plenty of tape.

Then, add two newspaper balls to the top of the head for eyes.

Now you have all your parts for the dinosaur, so it's back to the egg...

Take some scissors and make jagged cuts around the opening of the balloon to look like a broken shell. Be careful not to make the hole too big. You can always bend the edges slightly just to help get the dinosaur inside.

Then, put the dinosaur inside.

Start by taping the claws so that they're poking out of either side of the hole.

When they're secure, put the dinosaur head between them, again, using lots of tape to hold it into position.

Add a layer of PVA glue and tissue paper over the head and claws, to make them really solid.

When you've covered the dinosaur, and it's dry, you'll have something that looks like this.

It's now ready for painting...

It's up to you how you paint it. This dinosaur is green with darker shades and the egg is blue with purple spots.

When the paint is dry, you can then pick out all the detail with a black pen.

Now all the dinosaur needs is a nest...

Cut out a circle of cardboard box card that's about the same size as a dinner plate.

Scrunch up some long newspaper strips and wrap them around the outside of the circle, taping as you go, to build up the edge of the nest.

When you're happy with the shape, give the whole thing a base coat of brown paint

To make it realistic, paste on some PVA glue and stick on handfuls of hay. It can be quite messy so you might want to put down some newspaper or a flattened-out carrier bag before you begin.

When you've finished you'll be left with something that looks like this.

Place the dinosaur egg in the nest, and you're done.

Why not make two or three different types or egg, with different types of dinosaurs hatching from them?

Try it yourself!

最佳答案
本回答由提问者推荐

头像
匿名用户 4级
2009-10-13 回答
对于爪,使报纸的三个小香肠和磁带的一端在一起。再次这样做,你就会有两个爪子为头。,塑造成一个梨形排序一些报纸,弯曲的超薄结束在作出小,beaky鼻子。对于底部的下巴,造型为一个粗略的三角形一些报纸。棒,为下方的大量的胶带头。然后,将两家报纸球到头顶上的眼睛。现在,您对您所有的恐龙部分,因此它回到蛋...采取一些剪刀,并围绕气球开放锯齿状削减看起来像一个破壳。小心不要使洞太大。你总是可以稍微弯曲的边缘只是为了帮助获得恐龙里面。然后,把恐龙内。用胶带的魔爪,使他们扳手任孔方所启动。当他们的安全,把恐龙它们之间的头部,又用胶带把大量持有的地位。新增了头部和爪子的聚乙烯醇胶水和纸巾层,使他们真正奠定牢固的。当你所涵盖的恐龙,它的干,你要喝东西看起来像这样。现在它准备的画...这取决于你如何描绘它。这种恐龙是较深的色调和卵子绿色与紫色是蓝色斑点。当油漆干燥,然后你可以挑选出黑色钢笔所有的细节。现在,所有的恐龙需要的是一个巢...切出一个圆圈纸板盒卡,对作为一个餐盘的大小。堆砌了一些长条报纸和环绕在他们的圈子外面,盘带,当您去,建立了巢的边缘。当你满意形状,让整个事情的棕色油漆底漆为了让现实,在某些聚乙烯醇胶水粘贴,坚持一把干草上。它可以相当混乱,因此您可能要放下一些报纸或扁平出载波袋开始之前。当您完成您用的东西看起来像这样。放置在左侧窝恐龙蛋,即可大功告成。为什么不让两种或三种不同类型或同卵孵化他们不同类型的恐龙,?自己尝试一下!